Instrumentu Komplekts DeWalt DCK755P3T-QW 3x5Ah, 18V

Kit contains the the following: Brushless Combi Drill, Brushless Impact Driver, SDS Hammer Drill, Brushless Grinder, Brushless Multi-Tool, Brushless Circular Saw, Brushless Jigsaw, TSTAK II, TSTAK VI, TSTAK Mobile Storage

DCD796 Brushless Combi Drill

Compact impact drill/driver 18 V XR Li-Ion. Brushless motor technology guarantees excellent efficiency. Perfectly compact and light construction allows use even in places with limited access. The all-metal transmission with two transmission stages extends the operating time and service life of the tool. The hammer and the possibility of screwing guarantee the universal use of this tool. 15 positions for adjusting the tightening torque enable uniform screwing into different materials. The design of the intelligent trigger switch allows for maximum controllability while working. The improved ergonomic design with a rubber surface of the handle increases the comfort of the operator. A steel belt clip and magnetic tool holder provide the perfect storage solution. Part of the intelligent XR Li-Ion series guarantees efficiency and faster execution of the required operations.

TECHNICAL PARAMETERS:

• Battery type XR Li-Ion
• Power voltage 18V
• Max. moment (hard material) 70 Nm
• Max. moment (soft material) 27 Nm
• Idle speed 0 - 550/2000min
• Strokes 0 - 9,350/34,000min
• Chuck capacity 1,5 - 13 mm
• Max. hole diameter [wood] 40 mm
• Max. hole diameter [metal] 13 mm
• Max. hole diameter [masonry] 13 mm
• Length 190 mm
• Height 203 mm
• Width 67 mm
• Acoustic pressure 89 dB(A)

DCF887 Brushless Impact Driver

3-Speed Impact Driver DCF887 More runtime and capacity over standard units delivered by DEWALT-built brushless motor and lithium ion batteries. Optimized application versatility with 3-speed settings. Added control for precise applications with Precision Drive™ in speed 1 for precision applications and added control. Visibility without shadows from 3 LEDs with 20-second delay after trigger release. One-handed loading 1/4" hex chuck with easy grip sleeve, accepts 1" bit tips. Fit into tight areas with the compact and lightweight design. Variety of fastenings in wood, concrete and metal. Iron mongery, hardware fixtures and a variety of repair application.  Assembling ducts, air conditioning and central heating systems. Applications: Fastening extruded metal sheet to metal framen Fixing laps of roofing or cladding sheets and flashings, Fastening wooden frames together, Drilling, assembling and installing metal switchboxes, control boxes, etc.

• Max torque 240/1500/1825 lbf/ft
• No load speed (rpm) 0-1000 / 2800 / 3250
• Impact rate per min. 0-3800

DCH273 Brushless Rotary Hammer

The XR Brushless Rotary Hammer is a high-performance drill powered by a brushless motor and a durable German-engineered mechanism, delivering 2.1 Joules of impact energy. The lightweight design makes this tool ideal for rod hanging, seismic & safety attachments, cable tray & strut mounting, clamp mounting, and rail mounting. It is part of the PERFORM and PROTECT™ product line, integrated with the SHOCKS ACTIVE VIBRATION CONTROL® System and becomes OSHA Table 1 Compliant when used with the DWH303DH On Board Extractor. SHOCKS ACTIVE VIBRATION CONTROL System reduces vibration felt by the user at the handles, compared to rotary hammers without this feature. Lightweight design makes this tool ideal for rod hanging, seismic & safety attachments, cable tray & strut mounting, clamp mounting, and rail mounting. Brushless motor and durable German-engineered mechanism for efficient performance and runtime. Rotating Dial to set tool to a specific applicaiton mode - Drill, Hammer Drill, or Chip.

• Dlling capacity (concrete) 24 mm max.
• Drilling capacity (metal) 13 mm max.
• Drilling capacity (wood) 26 mm
• Impact energy (epta 05/2009) 2.1 J
• No load speed 0-1100 rpm

DCG405 Brushless Grinder

The DCG405 is a brushless angle grinder which is powered by DeWalt 18v XR lithium ion batteries. It has a slim and streamlined body with rubber overmoulding for excellent comfort, grip and control, while the compact angled gear head allows improved access to tight spaces. The machine is activated by a side mounted slide switch which has built in restart protection; a No-volt release system resets the switch in the event that the battery becomes depleted or detached while the grinder is in operation, thus ensuring it cannot start up by itself when power is restored. The DCG405 also has an electronic clutch and fast action brake, helping to safeguard against kickback or disc bursts and bringing spinning accessories to a rapid halt in under 2 seconds.

• Max. Disc Diameter: 125 mm
• No Load Speed: 9000 rpm
• Spindle Thread: M14

DCS355 Brushless Multi-Tool

The DCS355 20V MAX* XR® Lithium Ion Oscillating Multi-Tool has a powerful brushless motor providing up to 57% more run time over a similar brushed tool. The Quick-Change™ accessory system allows you to change blades quickly and easily, and with the universal accessory adaptor, it's compatible with most oscillating tool accessories. The DUAL-GRIP™ Variable Speed Trigger provides ultimate speed and application control, the DEWALT Oscillating Tool Guide System allows you to customize the depth or height for accurate repeatability, and the bright LED light illuminates dark work spaces.

• Oscillations speed: 0-20,000

DCS570 Brushless Circular Saw
This Circular Saw gives you with the power and depth-of-cut of a corded circular saw, but with the portability and convenience of cordless. DEWALT brushless motor technology delivers excellent performance and runtime when cross cutting 2x material and ripping sheet goods.

SPECIFICATIONS

• Bevel Stops 22.5 & 45 degrees
• Blade Diameter 7-1/4"
• Blade Size 7-1/4 In
• Depth Of Cut At 45° 2 In
• Depth Of Cut At 90° 2-9/16 In
• Electric Brake
• For Wood Cutting
• Brushless Motor 5500Rpm

DCS334 Brushless Jigsaw

XR® Cordless Jig Saw features an efficient motor for powerful performance and extreme runtime. Precisely control blade speed up to 3,200 spm with the variable speed trigger and dial, for professional results no matter what you're cutting. 4-position orbital action lets you adjust for optimal cutting of a variety of materials. A bright LED light illuminates dim work surfaces and makes it easy to follow cut lines. The updated all-metal, lever-action keyless blade clamp is designed for quick and easy blade changes of t-shank jig saw blades. Also keyless, the shoe bevel is easy to adjust with detents at 0°, 15°, 30°, and a positive stop at 45°. A removable shoe cover helps protect materials from scratches, and an integrated dust blower helps remove dust and debris from your line of sight as you cut.

• Nominal maximum rpm 910
• Max. cutting capacity (metal) 10 mm
• Dust solution compatible

Included:

• DCD796 Brushless Combi Drill
• DCF887 Brushless Impact Driver
• DCH273 SDS Hammer Drill
• DCG405 Brushless Grinder
• DCS355 Brushless Multi-Tool
• DCS570 Brushless Circular Saw
• DCS334 Brushless Jigsaw
• X3 DCB184 18V 5.0AH Batteries
• DCB115 Multi Voltage Charger
• TSTAK VI
• TSTAK II
• TSTAK Mobile Storage